What Heigth Rear Sight For Fixed Front Sight Ar 15

HuntingMark is reader-supported. When you buy through links on our site, nosotros may earn an affiliate commission. Learn More than

A front sight does not physically preclude a scope or optic from being mounted to the rifle. If you have a flip-up front sight and are non trying to co-witness with iron sights, so only flip the front sight down and install the scope normally. If you have a fixed front sight mail service (FSP), then yous might have some more difficulty.

A non flip-upwards FSP will obstruct the view of a depression magnification scope on an AR 15, and if yous don't properly co-witness a red dot or other not-magnified optic with your irons, information technology will exist distracting and difficult to shoot with. The FSP won't be visible at higher magnifications so your shooting should be but as accurate, on target, and your image as articulate and light as information technology would be without it.

Steps To Mountain Scope On AR 15 With Front Sight

Decide Whether You lot Desire Accented Or ⅓ Co-Witness

how to mount scope on ar 15 with front sight

In other words, do you want the rear and front irons to align perfectly with the red dot then they all three friction match up when y'all take the irons flipped up? Or do you want the front and rear sight to utilize the lower ⅓ of the view through the carmine dot? If yous've never shot with co-witnessed sights before it's hard to know the answer to that question. Here's my best shot at answering information technology:

I find if you have flip-up irons, then absolute co-witness works great because you lot're merely using the irons in case the red dot has an issue. If don't take flip-up irons, or the common combo of 1 flip-upward and the other on your ar 15 not, so I would recommend a ⅓ co-witness.

The reasoning is elementary: when I'one thousand using a reddish dot, the front sight just gets in the manner of the reticle, just I also like to have my cherry dot a picayune lower to the burglarize if possible.

Most AR-15s use standard heights for their iron sights, and reddish dots will unremarkably come with a riser elevation that is designed for either absolute or ⅓ cowitness. i-inch risers will requite y'all ⅓ cowitness while .83 inch risers volition ordinarily give you accented cowitness.

Telescopic rings aren't nearly as standard in size or to mount, but with a little research you can notice brusque, medium, and alpine rings to match the same gap level to become where you want the FSP to appear in your sight picture. Mounting isn't complicated, but to get the position right for shooting on your AR 15 can exist hard. Rest the gun on something to hold its position while you use your tools.

Remove The Sights, If Desired

how to mount a scope

The rear fe can exist fairly straightforward to do this with, only you need to exist careful with the front sight because it may take the gas block in it. If it does, if information technology were me I would just take information technology to a gunsmith and tell them what I wanted. Some things just aren't worth the risk of doing wrong.

The rear iron on the upper receiver of the ar 15 rifle should exist easy to remove. Just unscrew information technology from the flat part of the upper receiver. An AR fifteen with forepart sight can exist more complicated though. A crucial step is determining if the FSP is combined with the gas block of the gun. It'south just a matter of googling the rifle or rifles you have to encounter.

You can also consider swapping for a complimentary floating handguard, which besides improves accuracy and makes the process easier. Continue reading for the next footstep and the remainder of the steps to get your ar 15 rifles prepare for shooting.

Attach The Telescopic Mountain To The Rail Mount

mounting scope on ar 15 with front sight

How this is done depends on what kind of scope mount y'all have and what kind of scope, but assuming you have a ruby dot, and then the optic and telescopic mount may come attached and ready to merely clench right onto the rails. In most cases, y'all desire to use a chimera level to get the ar fifteen aligned vertically with the scope. That chimera level will come up in handy a few times.

If you have a scope and two rings, then there's a scrap more to it but your goal is merely to get them spaced where the scope can sit down at a comfortable altitude away from your middle. When you mount a scope, you may want a torque wrench to get the screws to a specific torque level. If you over tighten you tin crusade damage during the process, but a hex flake tool tin work too.

Most scopes can fit on the small picatinny that most AR weapon systems will come with, but you tin can go through all the steps to installing a costless floating rail if that will accept a positive effect on your scopes' position and brand things easier when trying to shoot accurately.

Attach The Telescopic To The Scope Mountain

mounting scope on ar 15 with iron sights

Again, if you're using a reddish dot, this may all be one stride, but if not, once you lot take the riser plate or mount in place, just attach the scope to information technology per its instructions. I'd recommend a torque wrench here too to get the sight completely attached only non besides tight. The rest is simple, make sure at that place's surface to surface contact around the unabridged scope, and avoid placing it too close to the barrel.

If using rings, you mount a scope by putting information technology in the lower rings then putting the upper rings on pinnacle of it. If you lot're co-witnessing, check where the reticle is in relation to the irons.

Tips

Here'southward the deal with magnification: if you're at a low power similar 2x-4x, then the FSP is going to obscure your sight moving-picture show to some degree. By all reports, if your magnification is college, especially in the 9x+ range, the obstruction of the front sight fades almost completely and is not even noticeable.

When I offset wanted to put a scope on my M&P 15, I concluded upward wanting to swap out the drop-in handguard for a complimentary floating rail so I could mountain a scope the way I wanted to, and that's something I recommend everyone do at some point.

Use a bubble level when you mount your scope on your rifle. Wait at your target through the scope during the mounting process to ensure accuracy with the weapon at that distance. Make clean the surface with rubbing alcohol. Tighten, but don't tighten likewise much. When you adjust after installing, do so gradually.

Final Thoughts

You can purchase a scope mountain or scope rings that get the scope as high or low as you need it on your AR15. You don't need many tools beyond the screws to secure the scope mountain or scope rings and the scope itself, a tool to tighten the screws, and a bubble level. All this is available for a reasonable price.

The mounting scope process is not as difficult every bit it may seem with the right tools, only you lot'll want to avoid mounting your telescopic where information technology's non secure on the gun or properly leveled. A scope or optic can aid you be more accurate when shooting your gun at the range and while hunting. For a short but helpful video on this topic, check out this from Caleb Downing on YouTube: